|
a series of comprehensive examinations on deadbolts and door knobs that not only proved informative, but also fun. First, the stars of this article consist of the hardware used on the door that weathered our violent attacks. The surviving hardware consisted of the following: 1. The new Schlage B660P series of deadbolts that have a beefier bolt assembly and stronger holding screws than that of the standard 400 and 100 series. 2. A MAG High Security Box Strike (Which states on the box that it will stop kick-ins it does and should be used with all deadbolts). 3. A Don-Jo classic wrap around door reinforcer that fits on the door under the deadbolt and door knob to stop the door from splitting it does, too. These three items can be seen in Photograph 1. And while they appear a little abused, they did work. So well, in fact, that despite the assault the deadbolt still operated.
The
doors and framing construction used for the test were standard
for residential applications. The rough frame was built to
standard residential construction, except the header, which
played little part in a security installation, using building
grade 2x4. The doors were standard residential steel clad doors
with wood rails or edges.
On
the first door I installed a ŗFaultless˛ deadbolt and door
knob purchased from a local Builderšs Square store.
In
the package the $12 deadbolt was nicely displayed and it
certainly looked good, at least to the uninformed public.
Photograph
2,
shows the installed Faultless door knob and deadbolt. The good
looks are only skin deep. The tools used in the torture test was
limited to those any homeowner or burglar would have around.
After only a couple of hits with the hammer, the deadbolt was
moved downward exposing the inner workings (see Photograph
3.)
At this point, the deadbolt is actually circumvented and compromised. This took about five seconds and two blows of the hammer. Photograph 4, shows our thug sticking a screwdriver into the hole to pull the bolt back.
Despite being able to open the door rather easily and quickly, we went a little further. Photograph 5, shows what happened after using the screwdriver and hammer to beat on the deadbolt a little longer. Still, it was decided not to open the door in this manner. Instead, I selected brute force, I got to kick the door open (I have always wanted to do this).
Backing
up a little, I leaned back and gently kicked the locked door. It
literally sprung open. The strike went flying as my size 13-1/2
shoe lightly touched the deadbolt. The
deadbolt strike screws functioned to help split the door frame,
and that was all (see Photograph 6).
Now we proceed on to the real test, the reinforced door and strike plate. The old battered door was removed and a new one rehung. After truing the door with shim stock, it was drilled and the guard plate was installed on the door. The reinforcement plate was also installed in the jamb. Photograph 7, shows the Schlage B600 series deadbolt being installed on the door. Photograph 8, shows the MAG 747 strike installed with two cover screws and two strike screws located on the inside of the box itself. All four screws are 2˛ in length giving excellent penetration of the jamb and frame (see Photograph 9).
The Don-Jo wrap around plate was then installed along with the deadbolt and a doorknob. For the next test we locked and attacked the door knob. As expected, the knob was circumvented with a pipe wrench in about eight seconds (see Photograph 10). After twisting the doorknob open with the wrench, it was hammered off. This was adding insult to injury. Nothing was really accomplished, except to prove the non-protective feature of the average door knob during a force attack.
The real test followed. The deadbolt was beat for about two minutes with the claw hammer. The results? Despite the marring and a few indentations, there is no circumvention here as before (see Photograph 11).
This deadbolt is designed with a bolt cover or guard and is seated into the face bore hole, preventing the lock from being knocked out of place. Even if a small opening was made, the bolt cover does not allow access to the bolt. The Don-Jo wrap around plate added further protection by not allowing the hammer to pierce the sheet metal of the door, allowing the lock to loosen or be exposed. The Don-Jo wrap around and the Schlage B600 withstood the first in a series of assaults. Not succeeding at knocking the lock off the door, it was then attacked with a screwdriver and hammer. This attack resulted in an unsuccessful attempt to punch the lock cylinder through the back of the lock resulted (see Photograph 12.)
Photograph 13, shows an attack with a pry bar. This had no effect on the security of the door, except to bend, mar, and disfigure the installation. It was now time to again, kick the door in.
The first kick was at the same force as that used earlier on the non-reinforced door with the Faultless deadbolt and knob. Despite a level 4 reading on the Richter Kick Scale, nothing happened. The kick force was increased to a level 7. While the door didnšt move, a couple of the supports for the door broke free. Nothing like having the house come down around the door! After replacing the door supports, the door was given one last gigantic, all-out effort kick, (level 9). Still, NO results. Not wanting to miss out on any of the self-abuse, several others in the testing lab added their own kicks, but none were so great as a 300 pound locksmith/safecracker could give. One torture tester backed up 20 feet and rushed the door yelling, ŗI have steel toed boots on.˛ He jumped up and kicked the door with a Karate kick that would have crushed most any door. Nothing happened. Then he turned around and backed up 30 feet. He concentrated, focused, and like a professional athlete he approached the door at warp speed, jumped, and gave that deadbolt a double diabolical Shudo-Kahn death kick. Again, the door withstood the competent attack that a lesser prepared door would have easily acquiesced to (see Photograph 14).
Unsuccessful, a strange smile crossed this torture testers frustrated face, slightly reminiscent of the Grinch before he burgled Who Village. Vaulting to a nearby YALE forklift, he stated that it was time for the door to DIE. Not wanting to crush the wall of the Testing Lab, he decided not to ram the door, and instead placed the forklift blades up against the door, putting gradual pressure against our reinforced locking system (see Photograph 15).
Once touching the door, he stepped on the gas. The wheels started turning, but the door and its hardware held. After increasing the speed, the door still did not open (see Photograph 16). At maximum speed the wheels burned through the floor tile and into the cement. Suddenly, and finally, the door crashed open.
The result! The strike plate split, the frame was slightly cracked and, except for two large dents from the forklift blades, the door remained unscathed (see Photograph 17). An incredible display of what some rather inexpensive additions to a deadbolt installation can do.
After viewing the damage, it was evident that the eventual strike box failure was due to the extensive twisting and bowing of both the door jamb and the framework. In a home, drywall and other wall components may make for an even more rigid framework, better supporting the strike, and making the entry even harder! So, while the forklift assault has not yet been added to the UL Standards Test, The National Locksmith Test Lab and demolition crew has provided you iron clad proof that you are safer when using the right equipment. These products really do work! The
products used in this test are just a sampling of available
products that can greatly increase door security. For more
information consult with a professional locksmith in your area. |
The
National Locksmith Testing Lab, recently did
